None FM-094 Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro ne None FM-094. none FM-094 Installation Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 1
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
FM-094
FM-094-1
FM-094-2
Installation
Manual
Operation and Installation Instructions
for FloodMaster Water Heater Leak
Detection Alarm/Shutoff System
Model FM-094 Series
27 Business Park Drive, Branford, CT 06405
Tel: 203-488-4477 • 888-771-4929 • Fax: 203-481-5036 • Email: info@floodmaster.com
www.floodmaster.com
System Overview:
The FM-094 line of Feed Water (Water Heater) Leak Detection
A
larm/Shutoff Systems is designed to sound an audible alarm and
s
hut down the water feed line when the sensor puck comes in
contact with conductive liquid (such as water). The unit requires an
110VAC wall outlet for power. In the event the alarm activates,
locate the source of the leak, remove the sensor puck from the water and dry the metal contacts at the bottom
of the sensor puck. Correct the problem causing the leak and replace the sensor puck in the desired leak
detection location once again as required. Press and release the red reset button on the alarm box to open the
valve and begin the flow of water again. The green power ON/OFF indicator light on the alarm box will flash
once to confirm the reset. All units provide an optional connection to a home security alarm system or control
panel. Additional sensor pucks can be added to the system where a wider area of leak detection is required.
Installation Instructions:
1. Turn off the water supply to the hot water heater.
2. As appropriate, either solder (FM-094) or thread (FM-094-1; -2) the valve body into the feed water line after the
manual shut-off valve, with arrow pointing towards the tank. For threaded installations, apply pipe sealant or Teflon
®
tape to the NPT threads and tighten. For solder installations, be careful not to get any flux or solder residue inside of
the valve body.
3. Install valve stem assembly into valve body. Tighten with a box wrench. Do not over-tighten.
4. Install power head and hand-tighten knurled nut.
5. Open water supply valve and inspect for leaks.
6. Place sensor puck on the floor or in the pan near the pressure relief valve drain tube.
7. Secure excess sensor puck cable to the drain tube using the supplied tie wraps.
8. If the unit is used without a pan, it is recommended that a continuous bead of silicone be laid on the floor that encircles
the hot water heater and sensor. This will help direct water flow towards sensor.
9. Plug the power cord into 110VAC wall outlet; the green power ON/OFF indicator light on the alarm box will turn on.
10. Function Test the system as follows:
a. Place sensor on a wet paper towel.
b. The alarm will sound and the valve will rotate (30 sec.) to the closed position.
c. Once the valve has completely closed, (30 sec.), open a hot water faucet and inspect for the absence of water
flow. There should be no flow.
d. Remove the sensor puck from the paper towel, dry the contact points and place the sensor puck back in the
desired leak detection location on the floor.
e. Press and release the red reset button on the alarm box. The green power ON/OFF indicator light will flash
once to indicate the reset has occurred.
f. Open a hot water faucet and inspect for water flow.
Maintenance:
Exercise (press and release) the reset button on the alarm box annually to ensure correct operation and to maintain
product warranty status.
Optional Feature and Connections:
Additional Sensor Pucks – For applications where a wider area of leak detection coverage is desired, additional sensor
pucks can be added to the system. Wire additional sensor pucks to the terminal strip along the side of the alarm box,
following the same wiring pattern of the original puck. Additional sensor pucks are sold separately; custom lengths are
available.
Security Alarm Connection – Use for applications where connection to a home security system or control panel is
desired. This dry contact relay signal can be wired per your application requirements as follows:
Red/White – Normally Closed Circuit
Black/White – Normally Open Circuit
Made in USA
ECN# 6205, 10/2011, MF-078, REV A
Zobrazit stránku 0
1

Shrnutí obsahu

Strany 1 - Installation

FM-094FM-094-1FM-094-2InstallationManualOperation and Installation Instructionsfor FloodMaster Water Heater Leak Detection Alarm/Shutoff SystemModel F

Komentáře k této Příručce

Žádné komentáře

Altronix AL400ULXB manuály

Uživatelské manuály a uživatelské příručky pro Napájecí adaptéry a střídače Altronix AL400ULXB.
Poskytujeme 1 manuály pdf Altronix AL400ULXB ke stažení zdarma podle typů dokumentů: Datový list


Altronix AL400ULXB Datový list (1 strany)


Značka: Altronix | Kategorie: Power adapters & inverters | Velikost: 0.13 MB |

 

Tabulka s obsahem





Další produkty a příručky pro Napájecí adaptéry a střídače Altronix

Modely Typ Dokumentu
AL62412CX Datový list   Altronix AL62412CX, 1 stránky
AL1012ULXB Datový list   Altronix AL1012ULXB, 1 stránky
T2428100C Datový list   Altronix T2428100C, 1 stránky
SMP10PM Datový list   Altronix SMP10PM, 1 stránky
AL802ULADA Datový list   Altronix AL802ULADA, 2 stránky
VR1T Datový list   Altronix VR1T, 1 stránky
VR2T Datový list   Altronix VR2T, 1 stránky
AL62412C Datový list   Altronix AL62412C, 1 stránky
AL600ULXD Datový list   Altronix AL600ULXD, 2 stránky
AL642ULADA Datový list   Altronix AL642ULADA, 2 stránky
AL400ULB Datový list   Altronix AL400ULB, 1 stránky
AL600ULXB Datový list   Altronix AL600ULXB, 1 stránky
AL176ULB Datový list   Altronix AL176ULB, 1 stránky
AL62424C Datový list   Altronix AL62424C, 1 stránky
AL125ULB Datový list   Altronix AL125ULB, 1 stránky
ALTV248ULHI Datový list   Altronix ALTV248ULCBHI, 2 stránky
VR5BT Datový list   Altronix VR5BT, 1 stránky
VR1 Datový list   Altronix VR1, 1 stránky
SMP5 Datový list   Altronix SMP5, 1 stránky
SMP10 Datový list   Altronix SMP10, 1 stránky